Correct preparation and application are what make the result good and long-lasting. Choose the product you are going to use, and follow the guide closely.
Always read the product label and the safety data sheet before use. We recommend testing the product on a small, inconspicuous area first.
ConGuardProtectionProtection for mineral surfaces
ConGuard is a water-based surface protection for concrete, brick, paving stone, roof tiles, natural stone, granite and rendered surfaces, among others.
- ConGuard
- Low-pressure sprayer, roller or brush
- Cleaning equipment
- Gloves and suitable protective equipment
- Covering sheets where needed
The surface must be clean, dry and free from dust, grease, algae, salt efflorescence and loose particles.
Remove any previous surface treatment that could stop the product from penetrating.
Cover glass, metal, plants and other areas that are not to be treated.
- Do not apply to a damp or frozen surface.
- Avoid applying in direct sunlight or when rain is likely.
- Clean the surface thoroughly.
- Let the substrate dry completely.
- Turn or stir the product gently before use.
- Apply ConGuard evenly with a low-pressure sprayer, roller or brush.
- Make sure the whole area is saturated without the product pooling.
- Remove excess product before it dries on the surface.
- Let the treatment dry and cure without exposure to rain or moisture.
- The product should penetrate the substrate and not form a visible layer.
- Absorbent substrates may need more product than dense ones.
- Always test on a small area first.
ConGuard+ProtectionWater- and oil-repellent surface protection
ConGuard+ protects natural stone, granite, marble, slate, ceramic tiles and finer concrete, among others, against water, oil and stains.
- ConGuard+
- Microfibre cloth, roller, brush or suitable applicator pad, low-pressure sprayer
- Cleaning equipment
- Gloves and suitable protective equipment
- Clean cloths for removing excess
The surface must be clean, completely dry and free from dust, grease, soap residue, limescale and previous treatments.
On dense or polished materials it is particularly important to test the product first.
- Do not let excess product dry on the surface.
- Avoid direct sunlight, high heat and the risk of rain during application.
- Gloss, texture or colour tone may be slightly affected on some materials.
- Clean the surface thoroughly.
- Rinse away all cleaning agent residue.
- Let the substrate dry completely.
- Turn or stir the product gently.
- Apply a thin, even coat.
- Work systematically so the whole area is covered.
- Remove product that does not penetrate before it dries.
- Let the surface dry and cure before it is exposed to water, oil or other loads.
- Apply several thin coats rather than one thick coat if the substrate requires it.
- Always test on a small, inconspicuous area.
TextileGuardProtectionProtection for textiles against water, dirt and stains
TextileGuard can be used on synthetic and natural fibres, including furniture, clothing, shoes, backpacks and other textile surfaces.
- TextileGuard
- Gloves
- Good ventilation
- A clean cloth for wiping up any spills
The textile must be clean, dry and free from dust, grease and stains.
Vacuum or wash the material if needed, and let it dry completely before treatment.
Always check the textile care label and test the product on a small, inconspicuous area.
- Do not use the textile before the treatment is completely dry.
- Do not spray on people or animals.
- Avoid inhaling spray mist.
- Some materials, colours and finishes may react differently.
- Clean the textile and let it dry completely.
- Shake or turn the bottle gently.
- Hold the bottle at an even distance from the surface.
- Spray a thin, even coat across the whole area.
- Avoid making the textile unnecessarily wet.
- Ensure good ventilation during and after application.
- Let the textile dry completely before use.
- Apply another thin coat if the material is very absorbent.
- Protect floors and nearby surfaces from spills.
- Always test the product first.
Anti GraffitiProtectionPreventive protection against graffiti
Anti Graffiti forms a protective film that makes graffiti easier to remove from masonry, concrete and other suitable mineral surfaces.
- Anti Graffiti
- Low-pressure sprayer, roller or brush
- Gloves and suitable protective equipment
- Covering sheets and masking
- Cleaning equipment
The surface must be clean, dry and free from dust, grease, algae, graffiti and loose particles.
Any damage should be repaired before the treatment starts.
Cover windows, metal, plants and areas that are not to be treated.
- Do not apply when there is a risk of rain or frost.
- Avoid direct sunlight and very hot surfaces.
- Some substrates may show a slight change in colour or gloss.
- Clean the surface thoroughly.
- Let the substrate dry completely.
- Stir or turn the product gently.
- Apply an even coat with a low-pressure sprayer, roller or brush.
- Ensure full coverage without runs or pooling.
- Apply several coats if the substrate requires it.
- Let each coat dry according to the product instructions.
- Protect the area from rain, dirt and contact while it dries and cures.
- The substrate must be completely clean and dry.
- The treatment may need renewing once graffiti has been removed.
- Always test on a small, inconspicuous area first.
Graffiti CleanerCleaningRemoval of spray paint, marker and graffiti
Graffiti Cleaner is designed for controlled removal of graffiti from suitable surfaces. The treatment should be adapted to both the surface and the type of paint.
- Graffiti Cleaner
- Brush, cloth or suitable applicator
- Soft or medium-stiff brush
- Gloves, safety goggles and protective clothing
- Clean water or the recommended washing equipment
- Equipment for collecting contaminated wash water and paint residue
Establish what type of surface and paint is to be treated.
Always test the product on a small area to check that the substrate is not damaged or discoloured.
Protect plants, glass, metal and surrounding surfaces.
- Do not let the product dry on the surface.
- A long dwell time can affect some substrates.
- Keep the product and contaminated wash water out of drains, soil and watercourses.
- Remove loose dirt from the area.
- Apply the product directly to the graffiti.
- Spread the product evenly with a brush or other suitable tool.
- Let it work for the recommended time.
- Work the area gently if needed.
- Remove the dissolved paint using the recommended washing method.
- Rinse the surface thoroughly.
- Repeat the treatment rather than using unnecessary force if any paint remains.
- Collect paint residue and wash water in line with applicable regulations.
- Always use suitable protective equipment.
- Ensure good ventilation indoors.
- Anti Graffiti protection normally has to be renewed after cleaning.
BioCleanCleaningCleaning of fungus, algae, moss and green growth
BioClean is designed to remove organic growth and discolouration from surfaces both indoors and outdoors.
- BioClean
- Low-pressure sprayer, brush or roller
- Scrubbing brush where needed
- Gloves, safety goggles and suitable protective equipment
- Water for rinsing where needed
- Covering sheets for plants and delicate materials
Remove loose dirt, moss and other loose material.
Protect plants, glass, metal and other nearby surfaces that are not to be treated.
Ensure good ventilation when used indoors.
- Do not mix the product with other cleaning agents.
- Avoid applying in direct sunlight or to a very hot surface.
- Remove loose dirt and growth.
- Dilute the product if the label or technical data sheet says to.
- Apply BioClean evenly to the area concerned.
- Let the product work for the recommended time.
- Work the area with a brush if needed.
- Rinse or finish the surface according to the product instructions.
- Repeat the treatment where growth is heavy or long-standing.
- Let the surface dry before any further treatment.
- Protect plants and surrounding materials.
- Wear safety goggles when working above shoulder height.
- Test the product on a small area first.
SuperCleanCleaningCleaning of limescale, rust and mineral dirt
SuperClean is a concentrated cleaner for removing limescale, rust, cement haze, grout haze, salt efflorescence and residue from mortar and concrete, among others.
- SuperClean
- Acid-resistant brush, sponge or suitable applicator
- Gloves, safety goggles and protective clothing
- Clean water
- A suitable container if the product is to be diluted
Check that the surface can tolerate acidic cleaning.
SuperClean must not be used on polished marble or other acid-sensitive materials.
Protect metal, glass, plants and surrounding surfaces.
Ensure good ventilation indoors.
- Must not be used on polished marble.
- The product must never be mixed with chlorine or other chemicals.
- Never let the product dry on the surface.
- Remove loose dirt from the surface.
- Wet the surface with clean water if this is recommended for the material.
- Dilute the product according to the product label and the degree of soiling.
- Apply the mixture in a controlled way to the area to be cleaned.
- Let the product work for the recommended time, but do not let it dry on the surface.
- Work the area gently with a brush or sponge.
- Rinse very thoroughly with clean water.
- Repeat the treatment if needed.
- Always test the material's acid resistance before treatment.
- Always use suitable protective equipment.
- Follow the stated dilution ratio closely.
Not sure about the right method?
Materials and surfaces can react differently. Always test the product on a small, inconspicuous area before treating the whole surface.
Get in touch if you are unsure which product you need, how the substrate should be prepared, or how the product should be applied.
contact@multicoating.no